Super Anchor 6151 Deluxe Tool Bag Harness – 4 Colors, 5 Sizes

Description

Super Anchor Safety Deluxe Series

6151 Deluxe Harness with All-Pakka Tool Bags

The Super Anchor 6151 is the 6101 Deluxe harness with the tool system built in: the same gray Tri-Lam3 padded frame, 6,000 lb polyester webbing, 5,000 lb D-rings, and quick connect buckles, combined with gray All-Pakka tool bags so the harness and bags work as one rig instead of fighting each other at the waist.

What is included: the Deluxe 3 D-ring harness with gray All-Pakka tool bag combo, in four webbing colors (Hi-Viz, Blue-Green, Red, Silver) and five sizes (S, M, L, LL, XL). Type A/P rated for fall arrest, restraint, and work positioning at 310 lb including tools. Compliant with ANSI Z359.11-21 (Intertek 11-2024), OSHA 1926.502, and CSA Z259.10-18.

6,000 lbWebbing Tensile Strength5,000 lbD-Ring Strength310 lbUser Capacity with Tools3D-Rings (Dorsal + Sides)14 inMax Harness Stretch4Webbing Colors5Sizes S to XLType A/PArrest / Positioning

Who Needs This Product

The 6151 is for production roofers and framers who carry their tools on their harness all day. A separate tool belt over a harness rides badly and blocks the positioning D-rings; the All-Pakka combo mounts the bags to the harness frame so weight transfers to the padded waist and shoulders. Fall arrest runs off the dorsal D-ring, positioning off the side D-rings, and the bags stay put through all of it.

Features

Tri-Lam3 padded frame

The SAS three-layer laminated frame pads shoulders and waist for all-day wear without pressure points.

6,000 lb webbing, 5,000 lb D-rings

1-3/4 inch polyester webbing with certified hardware and electrical discharge coating.

3 D-ring configuration

Dorsal D-ring for arrest and restraint plus side D-rings for work positioning.

Quick connect buckles

Chest and leg buckles snap in and adjust snug, with elastic keepers for loose webbing.

All-Pakka tool bags included

Gray All-Pakka bags mount to the harness frame so tools ride on the padding, not on a second belt.

5-size range with LL

Sizes S through XL including the long-large LL cut for taller workers.

Technical Specifications

Model	6151 series, 20 configurations
Webbing	1-3/4 inch (45 mm) polyester, 6,000 lb minimum tensile strength
Included Tool Bags	Gray All-Pakka tool bag combo mounted to the harness
Frame	SAS Tri-Lam3 padded frame, gray
D-Rings	Dorsal plus side positioning D-rings, 5,000 lb minimum strength
Buckles	Quick connect, ANSI/CSA certified connectors
Hardware Finish	Electrical discharge coating (EDC)
User Capacity	310 lb maximum including tools and equipment
Maximum Harness Stretch	14 inches, included in length of fall calculations
Rating	Type A/P: fall arrest, fall restraint, work positioning
Colors	Hi-Viz, Blue-Green, Red, Silver webbing
Sizes	S, M, L, LL (long-large), XL
Compliance	ANSI Z359.11-21 (Intertek report 11-2024); OSHA 1926.502; CSA Z259.10-18 (report on request)

⚠

Fit and fall clearance are life critical. Adjust the harness snug with the chest strap 8 to 12 inches below the shoulders and loose webbing stored in the keepers; a badly adjusted harness can allow the user to fall out during a free fall. Maximum harness stretch of 14 inches must be included in every length of fall calculation, and users connect only to rated D-rings with ANSI or CSA certified connectors.

Compliance Standards

ANSI Z359.11-21

Full body harness compliance verified by Intertek lab report 11-2024 per the 2025 manual.

OSHA 1926.502

Construction personal fall arrest system requirements.

CSA Z259.10-18

Canadian harness compliance with report available on request.

Type A/P Rating

Fall arrest, fall restraint, and work positioning use.

Typical Applications

Roofing CrewsAll-day wear on steep slope production work.FramingPositioning and arrest through the framing phases.Solar InstallationComfort for long install days on the roof.Commercial MaintenanceFacility crews needing positioning D-rings.Crew Color CodingFour webbing colors separate teams at a glance.High Visibility WorkHi-Viz webbing for congested sites.Tower and Ladder WorkWork positioning off the side D-rings.Contractor FleetsOne SKU family fits every worker size.

Installation Overview

Fit procedure per the 2025 manual:

1. Don the harness and connect the quick connect chest and leg buckles.
2. Set the chest strap 8 to 12 inches below the shoulders with the straps aligned vertically.
3. Adjust chest, leg, and waist belt snug with extra webbing stored in the elastic keepers.
4. Connect fall protection to the dorsal D-ring with ANSI or CSA certified connectors; side D-rings serve work positioning only.
5. Include 14 inches of maximum harness stretch in the length of fall calculation.
6. Inspect webbing, stitching, hardware, and labels before each use.

Inspection and Retirement

Inspect before installation and each use, with documented annual inspections. Remove the anchor from service when any of the following apply:

• Webbing shows cuts, burns, abrasion, or chemical damage.
• Stitching is broken or pulled at any load-bearing seam.
• D-rings, buckles, or adjusters are cracked, bent, or corroded.
• The harness arrested a fall; remove it from service immediately.
• PID labels inside the shoulder strap are missing or illegible.

Tag anchors removed from service to prevent further use until inspected by a qualified or competent person.

Fall Protection
Distributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your SRL or lanyard setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k). Run the Numbers and Stay Safe Launch the Calculator ›

Frequently Asked Questions

What sizes and colors can I order?Five sizes (S, M, L, LL long-large, XL) in four webbing colors (Hi-Viz, Blue-Green, Red, Silver), all on the gray Tri-Lam3 frame and all at the same price. Pick both in the options above and the photo updates to your color. See the Technical Specifications on this page for the exact materials, dimensions, and ratings.What is the LL size?Long-large: the length of an XL torso with the girth of a large, cut for taller lean workers who fall between standard sizes. Check the size chart PDF below. See the Technical Specifications on this page for the exact materials, dimensions, and ratings. Always inspect the product before each use and take it out of service if you notice any damage, deformation, or excessive wear.Is this harness rated for work positioning?Yes, Type A/P covers fall arrest, fall restraint, and work positioning: arrest and restraint connect to the dorsal D-ring, and positioning uses the side D-rings with a positioning lanyard. Make sure the connecting hardware and anchorage suit your application before you attach a lanyard or lifeline.What tool bags are included?The gray All-Pakka tool bag combo comes mounted to the harness. Bags are replaceable, and additional All-Pakka bags and hammer holders are available. Follow the recommended fastener pattern and placement so the connection is secure, and re-check the installation before you rely on it for fall arrest.How much can the harness stretch in a fall?Maximum harness stretch is 14 inches, and the manual requires including it in the length of fall calculation along with lanyard extension and D-ring height. Pair it only with connectors and equipment that are approved for use together so the complete system performs as designed.What standards does it meet?ANSI Z359.11-21 verified by Intertek lab report 11-2024, OSHA 1926.502, and CSA Z259.10-18 with the compliance report available on request. Following the manufacturer guidance on this page is part of keeping your equipment audit ready. Only trained workers should select, install, and use fall protection equipment for its intended application.How do I fit it correctly?Chest strap 8 to 12 inches below the shoulders with straps vertical, chest, legs, and waist snug, and loose webbing in the elastic keepers. An improperly adjusted harness can allow the user to fall out during a free fall. Pair it only with connectors and equipment that are approved for use together so the complete system performs as designed.

Super Anchor 6151 Submittals and Documentation

Deluxe Harness Instruction/Specification Manual 2025 (PDF)Materials, fit adjustment, harness stretch, D-ring use, and inspection requirements.Deluxe Harness Size Chart (PDF)Size selection chart for S through XL including the long-large LL cut.Super Anchor Warranty and Compliance Statement (PDF)Manufacturer warranty terms for Super Anchor fall protection equipment.

Compatible and Related Products

• Super Anchor 4020 3-Strand Value Lifeline. Lifelines in 25 to 100 ft lengths for harness tie-off.
• Super Anchor SuperGrab 4015 Rope Grabs. Fall arresters for lifeline work.
• Super Anchor SideWinder Cable SRL. Self-retracting lifeline in 20 and 50 ft lengths.
• Super Anchor 3013-D Hinge-2 Anchors. Reusable temporary roof anchors.

Outfitting a Whole Crew?

Send us sizes and colors by worker and we will build the order with lifelines and anchors so everything ships together, based on the delivery location.

Call 863-703-4522 to talk to a fall protection specialist.